I don't visit here much anymore so please post your interest so I can get an e-mail notification. Otherwise, you might be waiting a bit. Also, I'm not parting and the only trades accepted are those mentioned. Right now I need money to relocate and I'm getting out of the sport for the time being. Markers are sold as-is unless otherwise specified and because I'm not sure of the current market please don't be afraid to make an offer.

CCM Series 6 Prototype:



http://www.mcarterbrown.com/gallery/data/718/IMG_81501.jpg

http://www.mcarterbrown.com/gallery/data/718/IMG_81511.jpg

Description:

The marker itself is in pristine condition. The only visible blemish that I can see is on the pump kit. There is a small scratch on the "tightening nut". The 2 Liter is a little rough on the top collar and near the bottom but is in good condition overall. The SC feed is in good condition and comes with both the short and long feedtubes.

It can come with an AKA rail and CP ASA for a little extra. This was tuned by Total Greif's Kent Oxman before I used it last and I haven't had the opportunity to use it since. As far as I know it is the only Series 6 Prototype to have a factory dual rod kit installed.

Comes as shown. Inserts can be included but not immediately as they're in another state. It aired up without leaks two weeks ago so it should be fine. If the buyer chooses I can send it to CCM for check-up (I'll split the cost) before it arrives.

Price:

$600 o.b.o Shipped and Insured via UPS Ground

AGD Golden Gun #11 Pump 'Mag:

http://www.mcarterbrown.com/gallery/data/7...icture_0115.jpg

http://www.mcarterbrown.com/gallery/data/7...Gun_11_0111.jpg

http://www.mcarterbrown.com/gallery/data/718/IMG_63841.jpg



Description:

The top image shows how it all started. There are some flaws in the gold plate on the body (The plater had to evacuate during the California fires so I don't blame him, but you should know.). The marker was a user before I acquired it and for a short time after. There is some flaking on the valve body that was there when I bought it, as well as some scratching on the feed cap and some small dings on the rail.

It comes with two BOA barrels, a CCI Adjustable L-Stock (with an extra butt plate to make it an adjustable T-Stock), the CCM SC Feed, a CCI Bucket Changer, a Palmer's SC Feed, and the original PF body and Crown Point barrel. It is fully functional as a user and aired up without leaks when I used it last. It has been in storage for over a year now though so it may need some oil to get it back into shape.

Plus, if you buy this before the end of October you can remove me as competition for peanut butter nation's Pump of the Month. ;)

Price:

$900 o.b.o Shipped and Insured via UPS Ground

Please feel free to make an offer, but I won't be accepting trades at this time (unless it's a BNIB Makita 18v Drill and Impact Driver set, a gas card, airfare, or a job.).

CIP Super Stock:



http://www.mcarterbrown.com/gallery/data/718/IMG_7813.jpg

Didn't come with front of back sights when I bought it and it was also missing the feed tube. Never aired it up, shot it, etc. I bought it, got it, and it's been sitting disassembled in a box ever since. I had meant to ship it off to Carter for the missing pieces and then anodize it but... Life happened.

Price is set at $550 shipped. Shipping is USPS with Delivery Confirmation. (Insurance is optional but I would buy it.)

Brad Nestle Phuzzard:



This has been my go-to marker for years. It comes with a Punisher Speed Block and a gloss black Frantom I. The only issue I know about is that the screws going into the bolt have some flats worn into them. I don't know how or why, but they're there. They don't interfere with the markers operation but it does make them hard to get in and out. You also cannot torque down the pump arm screws because it messes with the pump stroke. I don't think that's a real issue, but I'm letting people know as a warning. I wouldn't mind keeping this one. ;) I believe I threw an L-Stock in the box, but I don't remember at the moment.

Price is set at $385 shipped. Shipping is USPS with Delivery Confirmation. (Insurance is optional but I would buy it.)

2002 AKA Excalibur:



http://www.mcarterbrown.com/gallery/data/754/IMG_8145.jpg

Description:

It's a user so it has its scratches and dings but overall it's in good condition. It has a few noticeable (but by no means large) dings and an area of scratching on the "stem" of the left side eye detent. It had a leak the last time I aired it up but it went away after I ran some oil through the marker. That was at the beginning of this summer.

It comes with a Bart Parts No-Rider, Function On/Off, WAS Board, JMJ trigger, SCM III, and a Rob-Town valve. It can be sent to Destructive Customs for a check up at the buyer's request (I'll split the cost.). This is one of my absolute favorites, but I'm getting out of the sport so it's going to go. Right now it really just sits and collects dust...

Price:

$625 Shipped and Insured via UPS Ground

No trades please.

-----------------------------------

I can't provide a shipping Zip Code because I don't have a permanent home right now. ;)

Hopefully this won't violate the "bump" rules.

Let's do 15% off anything over $500 and 10% off anything under until I post otherwise. I need money to relocate and get a job! Help me avoid signing up for unemployment.

Duzzy, best of luck on your sale although I'm sad to see it my friend. Hope things work out for you, and if ya need anything let me know.

P.S. Don't you dare sell your custom Merlin! (and if you have, shame on you!)

Do you know that the darn thing still isn't finished! It's only been 5 years since you last saw it and maybe 7 since I started... No, I'll finish that nightmare if it kills me.

Thanks for the kind words though, and someday we'll have to 'ball together again. It's been a long time though.............

Me too man, me too. Still got that Powerlyte Merlin?

Nah, that sold a while back.

Punisher's Phantom sold.

Price Drop.